How Much Is a Copper Pipe 1" (Type L) Worth in Scrap?
Scrap value: $1.68 – $2.35 as of Nov 10, 2026. That is what a typical Copper Pipe 1" (Type L) fetches at US scrap yards today. The exact payout depends on local prices, yard quality, and how well you've prepped the material.
| If the yard pays | You get |
|---|---|
| 50% of spot (typical low) | $1.68 |
| 60% of spot (typical) | $2.02 |
| 70% of spot (clean, sorted) | $2.35 |
What's inside a Copper Pipe 1" (Type L)?
One-inch nominal Type L copper water tubing, used for main service lines and trunk distribution in homes built before PEX adoption. Significantly heavier per foot than 1/2 in or 3/4 in, which makes even short runs from a main shutoff or boiler feed worth scrapping individually. Pays the standard clean copper-pipe rate when stripped of solder, fittings, and PEX adapters. Type K (thick-wall) is heavier still at ~0.884 lb/ft and pays the same per-pound rate.
| Material | Weight per unit | Per-lb rate (yard pays) | Per-unit value |
|---|---|---|---|
| Copper Pipe (Clean) | 0.65 lb | $2.57 – $3.60 /lb | $1.68 – $2.35 |
How to prep your Copper Pipe 1" (Type L) before scrapping
Strip all brass fittings and solder joints (sell brass separately at the yellow-brass rate, scrap leaded solder ends as #2 copper). Drain water fully and let dry to avoid weight downgrade. Cut into 4-6 ft sections and bundle by length for easier weighing.
Why prep matters: Most yards pay different rates for clean vs. mixed material. An hour of prep can roughly double your payout per pound on copper-bearing items.
What yards typically pay
90-day Copper Pipe (Clean) price estimate (US average) — the dominant material in a Copper Pipe 1" (Type L).
Find yards that buy Copper Pipe 1" (Type L) near you
Enter your ZIP to see scrap yards within 25 miles that accept this material.
Calculate value for your specific situation
Adjust the quantity, add other items, or enter your ZIP for a localized estimate.
| Material | Recovered | Rate | Value |
|---|---|---|---|
| Copper Pipe (Clean) | 0.65 lb | $2.57–$3.60/lb | $1.68 – $2.35 |
How are these prices calculated?
Each day we take metal spot prices from MetalpriceAPI and turn them into US average prices per scrap grade (spot × a grade factor; a few grades such as steel use fixed reference values). The calculator assumes a yard pays 50–70% of those grade prices, which gives the range you see. Full method.
Why a range?
Yards don't pay you the full grade price. They take a margin to cover transport, processing, and risk. The exact margin depends on grade quality, how clean the material is, local competition, and current end-buyer demand. The low end of our range is a conservative estimate; the high end is what well-prepared, clean material at a competitive yard can earn.
What affects your actual payout?
Preparation matters. Stripping copper wire to bare-bright roughly doubles the per-pound rate vs. selling it insulated. Removing brass fittings from copper pipe lets each metal sell at its proper grade instead of being downgraded to mixed. Quantity matters. Some yards offer better tiers for larger loads. Timing matters. Spot prices move daily; a 5% swing on copper is normal week-to-week.
Should I trust this estimate?
Treat it as a planning tool, not a guarantee. For large hauls, call two or three yards and ask for a per-pound quote on the specific grade. Don't haul anything more than 30 minutes without a quote — fuel costs add up. Most yards will quote over the phone if you describe the material accurately.
Related Electrical & Wire
Frequently asked questions
How much is Copper Pipe 1" (Type L) worth in scrap?
$1.68 – $2.35 as of Nov 10, 2026: that is the scrap value of a typical Copper Pipe 1" (Type L) at US yards today, based on its metal content (Copper Pipe (Clean) (0.65 lb)) and current prices. The exact payout depends on local prices, yard quality, and how well you've prepped the material.
What metals are inside a Copper Pipe 1" (Type L)?
A Copper Pipe 1" (Type L) contains: Copper Pipe (Clean) (0.65 lb). Per-component recovery rates and current prices determine the value.
Should I prep a Copper Pipe 1" (Type L) before scrapping?
Strip all brass fittings and solder joints (sell brass separately at the yellow-brass rate, scrap leaded solder ends as #2 copper). Drain water fully and let dry to avoid weight downgrade. Cut into 4-6 ft sections and bundle by length for easier weighing.
Where can I take a Copper Pipe 1" (Type L) to scrap?
Use the ZIP code form above to find scrap yards near you that accept Copper Pipe 1" (Type L), with distance, contact info, and accepted-materials notes.
Estimates assume yard payouts at 50–70% of national spot. Actual payouts vary by region, yard, and material condition. Last updated Nov 10, 2026. © 2026 Scrapyards.io